Temecula Roof Pros provides professional chimney & wall flashing in Temecula, CA for residential and commercial properties across the Temecula Valley. Flashing is where roofs meet things that are not roofs, and it causes more of the leaks we see than anything else. Wind makes it worse: water that would otherwise run down a wall gets pushed sideways and upward, so a detail built for gravity alone fails here.
The correct assembly has two independent parts. Step flashing, one piece per shingle or tile course, woven into the covering and turned up the wall. Then counterflashing, a separate piece let into a saw-cut reglet in the masonry or lapped behind the weather-resistive barrier under stucco, coming down over the step flashing. Two layers, mechanically overlapped, no sealant doing structural work.
What we find instead is one layer and a lot of caulk. Surface-mounted metal glued to the brick, or roofing cement troweled into the joint. It sheds water for a year while the sealant is flexible, then cracks, and by then it is hidden under a second application of the same. Removing that and cutting a proper reglet is the fix, and it is not expensive relative to what the water is doing inside the wall.
Chimneys wider than about thirty inches need a cricket on the uphill side: a small framed and flashed saddle that splits the water and sends it around instead of letting it pond against the masonry. Their absence is the reason so many stucco chimneys stain in a band across the back. Building one is a half-day of framing and metal, and it removes a permanent maintenance problem rather than deferring it.
Where a roof plane runs into a wall and stops at a gutter, a kickout flashing at the bottom of the step run diverts water out into the gutter rather than behind the cladding. It is a small piece of metal, it is routinely omitted, and the damage it prevents is the expensive kind. Both details are cheap while the roof is open and awkward afterwards.
On tile we use a wide soldered or mechanically seamed pan against the chimney with a generous upstand, cut the tile to sit clear of the vertical leg, and fit a rain diverter above wide masonry. Sheet metal formed on site fits the actual geometry, which a universal flashing kit never does. We bend our own on the truck for exactly that reason.
Our licensed and insured team brings the right materials and equipment to every job — ASTM D7158 Class H wind-rated laminate shingles, six-nail fastening inside the reinforced nail zone, hand-sealed perimeter courses in asphalt roof cement, stainless steel storm clips at rake courses, single-patty polyurethane tile adhesive, self-adhering SBS-modified peel-and-stick underlayment — and backs the work with a written workmanship warranty. We serve Temecula and nearby communities including Murrieta, Wildomar, French Valley, Winchester.
What We Handle
Everything our chimney & wall flashing in Temecula covers
One crew, one point of contact, and the full range of chimney & wall flashing work in Temecula, CA. If it is on this list we do it in house rather than handing it to a subcontractor:
- chimney flashing repair Temecula
- roof to wall flashing
- chimney leak repair Temecula CA
- step flashing replacement
- counterflashing reglet cut
- chimney cricket installation
- chimney chase cover replacement
- kickout flashing install
- flashing leak repair near me
- chimney flashing cost
- tile roof chimney pan
Not sure which one describes your situation? Describe it in plain words and we will sort it out — or browse the rest of our Temecula services.
Materials, equipment and how we do chimney & wall flashing
The difference between chimney & wall flashing that lasts and chimney & wall flashing that gets redone in three years is almost always preparation and materials, not the finish you see on day one. We work with ASTM D7158 Class H wind-rated laminate shingles, six-nail fastening inside the reinforced nail zone, hand-sealed perimeter courses in asphalt roof cement, stainless steel storm clips at rake courses, spec them to the job instead of to the invoice, and write the material grades into the free estimate so you know exactly what you are buying.
Every Temecula job runs the same way: site walk and measurements, written scope and fixed price, protection of the surrounding area, then the work itself with a daily clean-up. Years of roofing work in the Temecula Valley means we have already met whatever your property is going to throw at us — awkward access, older construction, an HOA with opinions.
Where we do chimney & wall flashing outside Temecula
Temecula Roof Pros covers Temecula and the surrounding communities of the Temecula Valley. Crews run out to the same nearby cities every week, so an out-of-town job does not mean an out-of-town price.
- Chimney & Wall Flashing in Murrieta, CA — Riverside County, population 110,949
- Chimney & Wall Flashing in Wildomar, CA — Riverside County, population 36,875
- Chimney & Wall Flashing in French Valley, CA — Riverside County, population 35,280
- Chimney & Wall Flashing in Winchester, CA — Riverside County, population 3,068
- Chimney & Wall Flashing in Menifee, CA — Riverside County, population 102,527
- Chimney & Wall Flashing in Canyon Lake, CA — Riverside County, population 11,082
Start on the Temecula Roof Pros homepage for a free estimate, or call (844) 511-2320 and describe the job.
Why Temecula Chooses Temecula Roof Pros
- ✓We quote attachment, not just material. Nails per piece, hardware at the perimeter, edge metal spacing and underlayment by elevation all appear on the estimate in writing.
- ✓We inspect the attic on every visit. Nail shiners, daylight at the rake, wind-washed insulation and delaminated sheathing tell you things the surface will not.
- ✓We price the repair when the repair is right. Refastening a perimeter and upgrading edge metal is often the correct spend on a roof with years left in it.
- ✓We will argue against products. Coatings do nothing for uplift and exposed-fastener metal panels fatigue under flutter, and we would rather say so than sell them.
The standards behind chimney & wall flashing
Quality here is not a matter of opinion — it is written down. The chimney & wall flashing work we do in Temecula follows published industry standards: NRCA publishes the Roofing Manual, the industry's reference for details and slope minimums, and Asphalt Roofing Manufacturers Association sets the shingle application and ventilation guidance the warranties reference. If a contractor cannot tell you which standard a detail comes from, that is worth asking about before you sign.
Every chimney & wall flashing project in Temecula gets the same attention, whether it is a single room or a full commercial job. We show up on schedule, keep the site clean, and stand behind the work — the estimate is free and there is no pressure.
Ready to get started? Call (844) 511-2320 for a free chimney & wall flashing free estimate in Temecula, or request a quote and we'll get right back to you.